Archive for the 'Tires and Wheels' Category
With the recent focus in Baltimore on improving fuel economy, we’ve been told how important it is to maintain our tire pressure.
Everyone in Baltimore knows that tires wear out, but we all want to make them last as long as possible because they’re fairly expensive to replace. In addition to saving gas, properly inflated tires last longer. Under-inflated tires will wear out more quickly.
Some people in Baltimore wonder if there is benefit to adding a few extra pounds of pressure when they fill up their tires. But actually, there isn’t. In fact, there are very good reasons not to over-inflate your tires. For one, the middle of the tread will wear unevenly because the full tread is not contacting the road properly. That also adversely affects your handling.
Come in and see us about tire maintenance for your Bowie , Maryland vehicle.
Council of Automotive Repair
1532 Pointer Ridge Place Suite G
Bowie , Maryland 20716
800-492-0329
Every vehicle in the Baltimore area has a sticker on the driver’s side door jamb that tells you the manufacturer’s recommended tire pressure. This recommendation is an integral part of the vehicle’s suspension tuning. A lot of engineering actually goes into the recommended tire pressure, so it’s important to follow it.
What else do we need to know about tire maintenance? Tire rotation and balancing are very important. Let’s start with rotation. Because the front tires handle the brunt of turning forces, the shoulders of the front tires wear more quickly than the rear tires. We rotate the tires so that they all get to do some duty on the front and they’ll all wear evenly over their life.
For most vehicles, front tires are rotated to the rear and vice versa. Others recommend a cross rotational pattern. Some vehicles use an asymmetrical tire so those tires need to stay on either the right or left side – it’ll say which on the tire. Some high performance cars have asymmetrical tires and different sizes on the front and rear. These can’t be rotated at all. Your owner’s manual will have details for your car.
How often should you rotate your tires? Your owner’s manual will have a recommendation. Your service advisor at Council of Automotive Repair can do a visual inspection to let you know if it looks like it should be done. The interval is typically around 5,000 miles.
You know, some people don’t think new tires need to be balanced. What they aren’t taking into account is the wheel. Between the wheel and the tire – even a new tire – there’s enough variation to require balancing.
When you add the valve stem and tire pressure monitoring sensors required on new cars, balancing is definitely in order. When a tire’s out of balance, it’s actually hopping down the road. You’ll feel the vibration through the steering wheel if a front tire’s out of balance and through your seat if it’s a rear tire.
Proper wheel balance promotes tire life and increases safety. Historically, lead weights have been attached to the wheel to bring it into balance. Lead gives some environmental concern, so steel weights are starting to be substituted.
Also, always use the same size tire on an axle. Different size tires on the front or on the back can lead to some real handling problems. And tire manufacturers recommend that when you get two new tires, they be installed on the rear because that’s where you need the most traction to avoid spinning-out.
Hey Baltimore, are your tires worn out? What is the standard for our Maryland streets? How can you tell on your SUV?
While there may be legal requirements for the Baltimore area, there are safety concerns that go beyond meeting minimum replacement mandates.
2/32 is the depth of the tire tread wear indicator bars that US law has required to be molded across all tires since August 1, 1968. When tires are worn so that this bar is visible, there’s just 2/32 of an inch – 1.6 millimeters – of tread left. It’s that level of wear that’s been called into question recently.
We’re referring to the Consumer Reports call to consider replacing tires when tread reaches 4/32 of an inch, or 3.2 millimeters. And the recommendation is backed by some very compelling studies.
The issue is braking on wet surfaces in and around Baltimore. Most of us think of our brakes doing most of the work, but if you don’t have enough tread on your tires, the brakes can’t do their job. When it’s wet or snowy, the tread of the tire is even more critical to stopping power.
Picture this: you’re driving over a water covered stretch of road near Baltimore, Maryland. Your tires must be in contact with the road in order to stop. That means that the tire has to move the water away from the tire so that the tire is actually contacting the road and not floating on a thin film of water.
Floating on the surface of water is called hydroplaning. So if there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.
In the study a section of a test track was flooded with a thin layer of water. If you laid a dime on the track, the water would be deep enough to surround the coin, but not enough to cover it.
A car and a full-sized pick-up were brought up to 70 miles per hour, or 112 kilometers an hour and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths:
- New tire tread depth
- 4/32 of an inch
- 2/32 of an inch
So what happened with the 2/32 tires on the car? Get this – when the car had traveled the distance required to stop with new tires, it was still going 55 miles an hour. Stopping distance was nearly doubled to 379 feet and it took 5.9 seconds.
Wow! That means if you barely have room to stop with new tires, you would hit the car in front of you at 55 miles an hour with the worn tires.
Now, with the partially worn tires – at 4/32 of an inch – the car was still going at 45 miles an hour at the point where new tires brought the car to a halt. It took nearly 100 feet more room to stop and 1.2 seconds longer. That’s a big improvement. We can see why Consumer Reports and others are calling for a new standard.
Of course, stopping distances were greater for the heavier pick-up truck.
How do you know when your tires are at 4/32 of an inch? Easy; just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.
You may remember doing that with pennies. A penny gives you 2/32 to Abraham Lincoln’s head. The quarter is the new recommendation – 4/32.
How do people feel about replacing their tires earlier? Well, tires are a big ticket item and most people want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out?
For us, and we would guess for many, the answer is “no”.
Council of Automotive Repair
1532 Pointer Ridge Place Suite G
Bowie , Maryland 20716
800-492-0329
All new passenger vehicles on our Bowie Maryland roads now have tire pressure monitoring systems – TPMS for short. They are designed to alert you if your tires are under inflated. Since they are fairly new, a lot of people have questions about TPMS.
First off, the most important thing is that you still need to check your tire pressure every week – or at least every time you gas up. The TPMS system alert comes in when your tire is twenty percent below the factory recommendation. So if the recommended pressure is thirty five pounds per square inch, the TPMS warning won’t come on until the pressure is at twenty eight pounds. That’s significantly under-inflated. Enough to raise safety concerns.
The worst is tire failure. A severely under inflated tire can overheat and fail. Also, handling degrades to the point that you may not be able to steer out of trouble. Also under-inflated tires wear out faster and they waste fuel. So it’s costly to not stay on top of proper inflation.
What’s the practical value of the TPMS system? Well, it’s twofold. First, it can alert you when your tire is losing pressure due to a puncture or a bent rim. That’s an important warning that you might not have gotten until next time you gassed up.
The second is that we all occasionally forget to check our tire pressure. So it’s a failsafe system to let you know there’s a problem brewing.
Other things can cause your TPMS system to go off. The system also monitors itself. The sensors that are mounted in the wheels have little batteries that send a signal to the monitor. The batteries go dead over time and the TPMS system will let you know. And the sensors could break. Also road salt from our Bowie Maryland roads can ruin them.
There’s also a hassle factor that your Bowie Maryland tire center has to contend with. For example, when you have your tires rotated in Bowie , the TPMS system has to be re-calibrated so that it knows which tire is on which corner of the car. Same is true for when you have new tires or winter tires installed. Flat repairs, as well.
That takes extra time. And it requires the right equipment and training. Special – and expensive – tire change machines need to be used with some sensors. It’s all complicated by the fact that there are a number of different TPMS systems in use so the tire professionals at Council of Automotive Repair need equipment and training for each kind. Tire centers have had to raise the price of some of these basic services to offset their increased costs.
Also if you add custom wheels on your SUV, you need to put in new TPMS sensors if your originals won’t work on the new rims. If you don’t your TPMS light will be on constantly and you won’t have the benefit of the warning system.
All in all, the mandated TPMS systems will save lives, so they’re worth the added hassle and expense.
So, when are your tires actually worn out? This is a question a lot of us in Bowie Maryland ask ourselves. For many, the answer is ‘when they no longer pass a safety inspection’. But waiting that long can have a serious impact on your safety.
The U.S. Federal government doesn’t have any laws for tread depth, but 42 of the states, and all of Canada, do have regulations. They consider two-thirty-seconds of an inch to be the minimum legal tread depth. Two other states, including California, consider one-thirty-second to be the minimum and six states have no standards at all. Call us at Council of Automotive Repair (just call 800-492-0329) to find out what your requirements are in the Bowie Maryland area.
Since 1968, U.S. law has required that a raised bar be molded across all tires. When tires are worn enough that this bar becomes visible, there’s just 2/32” of tread left. But does that older standard give you enough safety?
Well, Consumer Reports issued a call to consider replacing tires when tread reaches 4/32”. And the recommendation is backed by some very compelling studies. Now before we go into the studies, you need to know that the big issue is braking on wet surfaces.
We tend to think of the brakes doing all the stopping, but you also need to have effective tires to actually stop the car. When it’s wet or snowy in Bowie Maryland, the tread of the tire is critical to stopping power.
Picture this: you’re driving over a water-covered stretch of road. Your tires actually need to be in contact with the road in order to stop. That means the tire has to channel the water away so the tire is actually contacting the road and not floating on a thin film of water – a condition known as hydroplaning. When there’s not enough tread depth on a tire, it can’t move the water out of the way and you start to hydroplane.
This is where the studies come in. We think you’ll be surprised. A section of a test track was flooded with a thin layer of water. If you laid a dime flat on the track, the water would be deep enough to surround the coin, but not enough to cover it.
A car and a full-sized pick-up truck were brought up to 70 mph and then made a hard stop in the wet test area. Stopping distance and time were measured for three different tire depths. First, they tested new tires. Then tires worn to legal limits. And finally, tires with 4/32” of tread were tested – this is the depth suggested by Consumer Reports
When the car with the legally worn tires had braked for the distance required to stop the car with new tires, it was still going 55 mph. The stopping distance was nearly doubled. That means if you barely have room to stop with new tires, then you would hit the car in front of you at 55 mph with the worn tires.
Now with the partially worn tires – at the depth recommended by Consumer Reports – the car was still going at 45 mph at the point where new tires brought the car to a halt. That’s a big improvement – you can see why Consumer Reports and others are calling for a new standard.
Now without going into all the details, let us tell you that stopping the truck with worn tires needed almost 1/10 of a mile of clear road ahead to come to a safe stop. Obviously this is really a big safety issue.
The tests were conducted with the same vehicles, but with different sets of tires. The brakes were the same, so the only variable, was the tires.
So, how do you know when your tires are at 4/32”? Well, it’s pretty easy. Just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.
Now you may remember doing that with pennies. But a penny gives you 2/32” of an inch to Abraham Lincoln’s head. The quarter is the new standard – 4/32”.
Tires are a big ticket item and most people in Bowie Maryland want to get the most wear out of them that they can. But do you want that much more risk just to run your tires until they are legally worn out? For us, and we would guess for many, the answer is “no”.
Well, Mr. Washington, let’s go out and look at my tires.
Council of Automotive Repair
1532 Pointer Ridge Place Suite G
Bowie , Maryland 20716
800-492-0329
Let me start by saying that your wheel bearings keep the wheels on your vehicle. Did that get your attention? In this article we’ll discuss more about wheel bearings and how you can keep them doing their very important job while you drive around Washington D.C. Maryland.
Come see us at: 1532 Pointer Ridge Place Suite G Bowie , Maryland 20716
Wheel bearings are pretty simple parts. They’re made of high quality steel and are engineered to last 100,000 miles or more if properly cared for. The bearings do two very important jobs: First they allow the wheel to freely rotate with as little friction as possible. Second, they support the weight of the vehicle. For example, if your car weighs 3,600 pounds, each wheel has to support approximately 900 pounds. That’s a lot of heavy lifting over many, many thousands of miles.
Even though wheel bearings are relatively simple, they need to be in near perfect condition to do their job. The bearings are packed with heavy grease to lubricate and protect them. A seal keeps the grease in and water and dirt out. It’s when the seal starts to leak that problems begin. The grease can become contaminated; causing the wheel bearings to overheat and ultimately fail.
The first sign that your wheel bearings are in trouble is an unusual noise coming from a wheel. It could be a chirping, growling, rumbling or a cyclic sound. The noise could get louder or even disappear at certain speeds. Your technician at Council of Automotive Repair can inspect for bearing wear by lifting the vehicle and checking for play in the wheel.
Now some wheel bearing assemblies are factory sealed. That means that they cannot be serviced – they can only be replaced. Those that aren’t sealed can be serviced on schedule. The bearings are removed, cleaned and inspected. If the bearings are still good, they’re re-installed – if not, they’re replaced. They are then packed in grease and a new seal is installed.
If your vehicle has a factory sealed wheel bearing assembly, the entire assembly needs to be replaced when trouble arises. Unfortunately, the parts are pretty pricy – but they usually last about 150,000 miles as long as the seals hold up.
Now, even a good seal cannot keep out water that’s exerting pressure on the seal. So if you’ve driven through hub deep water your bearings should be cleaned and repacked if they’re serviceable. If you have factory sealed bearings, you just need to watch for signs of premature failure.
If your wheel bearings can be serviced, your owner’s manual will recommend an interval, usually around 30,000 miles.
Now, if you have any sort of trailer, don’t forget its wheel bearings. They probably need to be serviced even more frequently. This is especially true for boat trailers that are used to launch the boat by backing it into the water. These should be serviced every year, usually at the end of the season so that the bearings don’t have the opportunity to sit and rust all winter.
So what happens if wheel bearings fail? Well, the wheel can literally fall off the vehicle. I don’t need to tell you how bad that could be. So check with your service advisor at Council of Automotive Repair and see if your vehicle’s wheel bearings can be serviced and when it’s recommended. Listen for warning signs. If you’ve been fording streams or puddle surfing after rainstorms, be especially vigilant.
Come by Council of Automotive Repair for a wheel bearing inspection, or for Inspection. Call for an appointment at 800-492-0329
What type of technology do you use? Do you prefer an 8-track tape or an iPod? When it comes to winter tires, much of the public’s perception dates back to when 8-track was the best way to listen to the Bee Gees.
Twenty years ago, winter tires differed from highway tires only in their tread design. We called them snow tires back then and they had big, knobby lugs that were designed to give good traction in deep snow. They had the same rubber compound as regular tires and they weren’t very good on ice, packed snow or wet roads. They were not even very good on dry roads. They really helped in deep or loose snow, but they did a poor job the rest of the time. They were loud and rode hard. You couldn’t wait to get them off in the spring.
Then all-season tires started to come along. All-season tires are really a compromise between summer and winter performance. They have acceptable hot weather ride and tread life, and you can get through mild winter road conditions OK. But there are some really good reasons to consider winter tires.
Modern winter tires do a terrific job in a wide range of winter conditions. First of all, below 45 degrees Fahrenheit, regular tires become hard and inflexible. That means they don’t provide the road grip you need. Even if you don’t live somewhere with a lot of snow, but it still gets below 45 degrees in the winter, you will be safer with winter tires.
In addition, they are specifically designed to more effectively move snow and water. That’s the key to traction on ice, packed snow and wet roads. They use a micro-pore compound that allows the tire to bite into ice and snow. They also use wider grooves that run around the circumference of the tread to expel snow from the tire better. The lugs and grooves on winter tires have a special shape that throws the packed snow out of the tread as the tire turns. The tread is then open when it comes back in contact with the road and can provide good traction.
Winter tires also have a lot of sipes. Sipes are thin slits in the tread. The edge of the sipes grab ice and packed snow to provide tons of traction and to expel water and slush out of the tread. winter tires have a rounder casing to cut into the snow’s surface. The treads on regular summer tires can actually get packed with snow instead and become very slick. winter tires offer 25% to 50% more traction than all-season tires. And when it comes to stopping power, all-season tires take 42% longer to stop than winter tires. Sometimes that’s the difference between getting home safely and spending the night in a snow bank.
Now back when the 8-track was king, you just put snow tires on the drive wheels. That worked out OK because the rubber compound was essentially the same. Now, winter tires provide so much more traction than all-season or summer tires, that there’s a huge difference between the traction at the front and rear ends of the car if you only put winter tires on the drive wheels.
For example: if you take a corner on an icy road and the rear end starts to slide out, essentially the rear is trying to pass the front because it’s going faster. If you have high traction winter tires only on the front, they are going to be much more effective at transferring cornering grip and stopping power to the front wheels. This will actually cause the rear end to whip out even more.
That’s why tire manufactures instruct their dealers that they must install winter tires on the rear wheels as well whenever they put winter tires on the front end of any vehicle. It’s a major safety concern. It’s strongly recommended that winter tires be installed on all four wheels on rear wheel drive vehicles as well. The front tires do most of the steering and braking work – it only makes sense that you provide the front end with the best traction you can.
People often assume that if they have four-wheel drive or all-wheel drive they don’t need winter tires on all four wheels. Would you intentionally disconnect the four-wheel drive in poor road conditions? Of course you wouldn’t, but that’s essentially what you do if you only put winter tires on one end. It only makes sense to have the same level of traction and control at all four corners.
The province of Quebec in Canada has issued a law requiring all passenger vehicles, taxis and rental cars with Quebec license plates to install a full set of four winter tires between November 15th and April 1. It’s that important.
Many modern cars have traction control and anti-lock brakes so people may think that they don’t need winter tires. But you need traction to accelerate, steer and stop. The tires provide the traction so that the traction control and anti-lock brakes have something to work with.
Look for tires with the symbol of a mountain with a snowflake in it. This means the tire complies with the severe snow standard. All-season tires will have an M&S, for mud and snow, on the sidewall.
So when the temperatures drop below 45 degrees, be sure you have a set of four winter tires for maximum performance in snow, packed snow, ice, wet and dry roads. Your tire professional can help you find the right winter tire for your vehicle and driving needs.
Everyone in the Baltimore area wants our tires to last as long as possible. Two ways to maximize tire life are wheel balancing and tire rotation.
When wheels are out of balance, they wobble a bit. That makes the tires wear in a cupping pattern. And they vibrate. To fix this, your service technician at Council of Automotive Repair puts weights on your wheels to balance them out. If a front wheel is out of balance you’ll feel it in the steering wheel. If it’s a rear wheel you’ll feel it through your seat.
That brings us to tire rotation. The front tires on a car wear out more quickly than the rear tires. As they push through turns from Bowie to Baltimore, the shoulders of the front tires wear down. So rotating front and rear tires allows them to all wear at about the same rate over the life of the tire.
Proper tire inflation will also help your tires last longer. Under-inflated tires wear excessively on the shoulder and may even overheat. This could cause tire damage or a blow out. Over-inflated tires wear to fast in the middle.
Four wheel drive trucks and SUV’s tend to wear their tires more unevenly so rotation is even more important with them. Give us a call to get our recommendation on your SUV.
See your owner’s manual or ask your service technician at Council of Automotive Repair for your recommended tire rotation schedule. It’s usually every 5,000 to 8,000 miles.
Tires cost a lot and they are one of the most critical safety components on your vehicle. Take care of them and they’ll take care of you.
Council of Automotive Repair
1532 Pointer Ridge Place Suite G
Bowie , Maryland 20716
800-492-0329
Some of us just love tires. All those little rubber hairs on new tires and the smell is wonderful. We live in a great time for tires. No matter how you drive, where you want to go or the look you’re after; there is a tire for you.
The same is true about wheels. The hardest part is choosing from the thousands of wheels available.
We may not be able to help with that, but we can help you get some things in mind before you consult with your Bowie tire professional. Let’s start with function and think about how you drive.
For example, maybe you have a large SUV but you don’t drive off-road, so an off-road tread isn’t important. Also, because you are not out bouncing over rocks in the Maryland backcountry, you don’t need a high profile tire to protect your rims. So that means you can probably go with the low-wide look.
If you have a winter season with rain and snow or if you find you need better ice and snow performance, they make great, high-performance snow tires that won’t make it look like you are driving a tractor.
There really are a lot of options for any given vehicle. You will find it very helpful to have a discussion like this with your Baltimore tire pro when you need new tires. You can find the best solutions for your driving needs and to make improvements in ride or handling.
Picking a wheel that is the same size as what you are now running is pretty simple. But, it gets trickier if you want to upsize. Just get some help when you go bigger. All that tire and wheel still needs to fit in the available space. You do not want your tires to rub when you turn or hit a bump. You also need to make sure your brakes and suspension bits will fit with your wheel of choice. It doesn’t matter how great your car looks if it’s not drivable.
Taller, wider wheels and tires probably weigh more than your stock shoes. And it’s “unsprung” weight – that has a big impact on brake performance. The upsized shoes increase rotational inertia – if you go too big you may need to upgrade your brakes to compensate.
Another possible problem is an inaccurate speedometer. This happens because the number of rotations can change with the new wheels. Fortunately, speedometers and odometers are all controlled by the engine computer; so it is simple to get it reprogrammed and compensate for the bigger tires.
No matter what you are after: low cost, long life, high performance, traction or stunning good looks, your wheel and tire professional at Council of Automotive Repair in Bowie , Maryland can help you identify your needs and give you a custom fit. With all the options available, you don’t have to compromise. There is a tire out there with your name on it!
Tires do a lot of work. They transfer engine power and braking forces to the road; they handle steering control; and they cushion all those bumps and jolts. They also support the entire weight of the vehicle, including you and your passengers. With such critical work to do, you want your tires to do their job well. And since replacing tires is fairly expensive, you want them to last as long as possible.
There are three keys to long, even tire wear:
The front tires on a car take the brunt of the steering forces. As they push through turns, the shoulders of the front tires wear down more quickly than the rear tires. Rotating front and rear tires allows them to all wear at about the same rate. That’s especially true of front wheel drive vehicles whose front tires steer, and put the power to the road.
SUVs and pick-ups, especially four wheel drives, also tend to wear their tires more unevenly than cars because of their suspension and drive train set-up. Your owner’s manual will likely contain a schedule for tire rotation. It’s usually every 5,000 miles or so.
Also, there are different rotation patterns for different vehicles. Council of Automotive Repair will know which is right for your vehicle. That brings us to wheel balancing. When wheels are balanced, they spin on the axel evenly. When they are out of balance, they wobble a bit. That makes the tires wear unevenly and may transmit a vibration to the car. Your service technician at Council of Automotive Repair puts weights on your wheels to balance them out so that they turn true and smooth.
Tires are a big investment for any vehicle. They’re critical for keeping you safely on the road. The cost for regular rotation and balancing is more than made up in extended tire life. And, can you really put a price on your safety and that of your passengers?
Most folks have had a flat tire. You know it’s inconvenient and a pain. Our tires are important. Keeping them in good working order isn’t just a big safety issue – it also has a financial impact. With high gas prices, we’ve all heard about the importance of keeping proper tire pressure to save on gas. In addition, proper inflation promotes even tread wear so your tires last longer.
There’s another danger to under-inflated tires. Low tire pressure puts added stress on the structure of the tire itself, causing it to break down prematurely. Also, under-inflated tires generate more heat which also reduces tire life. So get those slow leaks fixed quickly – don’t just keep airing them up every few days. You want to avoid serious tire damage.
Tires can also be damaged by road hazards . Punctures, cuts and impacts on curbs or potholes can also cause damage that could lead to tire failure. Sometimes, it’s something that a visual inspection would reveal. Take the opportunity to check your tires when you’re gassing up. Look for slashes, missing chunks, nails or screws in the tread or just uneven wear. Of course check the air pressure too.
Now tire damage can be on the inside where you can’t see it until it’s removed from the wheel. Such damage could come from a severe impact, driving on a flat or even just low pressure. Some punctures can cause internal damage that are too severe to be repaired. You may see our Council of Automotive Repair professionals take the time to remove your flat from the rim and inspect the inside before repairing it, which means we’re just following good procedure.
Now some tires just can’t be repaired. A puncture may be too large to plug. Also, the puncture could be in a location that’s not safe to repair like in the sidewall or outer portion of the tread. So called run-flat tires should not be repaired because their design is such that internal damage can’t be detected by a visual inspection.
It is also important that repairs should only be done by a qualified tire specialist like the ones we have at Council of Automotive Repair. You can buy self repair kits – save those for emergencies, like when you’re off-roading and need a quick fix so you can hobble back to civilization and get professional help. If you need to use a repair-in-a-can product, remember it’s a temporary measure only and your tire needs to be properly repaired as soon as possible.
Here are some other considerations: Repairing a flat may void your tire manufacturer’s warranty – just something to keep in mind. Also, if you repair a speed rated tire, you should not use it in any motorsports or operate it above legal speed limits. Your tire professional will repair your tire whenever it’s safe to do so and he’ll advise you when it’s better to replace it. So watch those curbs and keep the air – on the inside.